 Replacing trunk hinge, Success, and hinge bolt mod. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Olympic 914 |
 Dec 4 2018, 02:38 PM
Post
#1
|
 Group: Members Posts: 1,707 Joined: 7-July 11 From: Pittsburgh PA Member No.: 13,287 Region Association: North East States 
 |
Going to have to repair/replace the trunk hinge on the car this winter. It was repaired before.... but it failed in a different spot. I wonder if the trunk lid gasket was too tight and caused this failure?
I am planning on taking the engine out to make it easier to get in there and position it correctly and do a good job welding. How many of you have done this repair leaving the engine in?   I am not an experienced welder and trying to weld it while bent over the fender and trying to even get the mig in there seems too hard. I have already had the engine out twice since last Oct. so I am getting quite good at it. |
   |
 
|
  |
Replies
| 914werke |
Dec 4 2018, 06:34 PM
Post
#2
|
|
"I got blisters on me fingers" Group: Members Posts: 10,934 Joined: 22-March 03 From: USofA Member No.: 453 Region Association: Pacific Northwest
|
The failure mode isn't tension, but rust. Or more precisely lack of lubrication that leads to rust. Once the shoulder bolt wears out its lube, its the beginning of the end.
|
 |
|
| 914_teener |
Dec 4 2018, 06:54 PM
Post
#3
|
|
914 Guru Group: Members Posts: 5,248 Joined: 31-August 08 From: So. Cal Member No.: 9,489 Region Association: Southern California |
QUOTE(914werke @ Dec 4 2018, 04:34 PM)  The failure mode isn't tension, but rust. Or more precisely lack of lubrication that leads to rust. Once the shoulder bolt wears out its lube, its the beginning of the end. Looks like shear to me. |
|
|
|
Posts in this topic
Olympic 914 Replacing trunk hinge Dec 4 2018, 02:38 PM
mepstein If you don’t need it to be original, Jwest makes... Dec 4 2018, 02:40 PM
jcd914
If you don’t need it to be original, Jwest make... Dec 4 2018, 06:10 PM dr914@autoatlanta.com engine in easy if you can spot weld, and now with ... Dec 4 2018, 05:14 PM dr914@autoatlanta.com by the way in the back of the tech tips 700 is the... Dec 4 2018, 05:15 PM Olympic 914
by the way in the back of the tech tips 700 is th... Dec 4 2018, 05:59 PM dr914@autoatlanta.com the bottom of page 132
by the way in the back o... Dec 5 2018, 03:22 PM Olympic 914 Damn.... My copy only goes to pg 125. :huh: :hi... Dec 5 2018, 06:05 PM amfab +2 for the JWest system.
Hardest part was getting ... Dec 5 2018, 02:58 PM rgalla9146 See current thread...'Replacing bracket for h... Dec 5 2018, 08:10 PM Tdskip I haven't done it (yet) but I believe the JWes... Dec 6 2018, 08:16 AM Olympic 914 OK, decided to pull the engine to do this job.
... Jan 26 2019, 03:00 PM second wind
OK, decided to pull the engine to do this job.
... Jan 27 2019, 01:44 PM 914forme :agree: They look great, that trick was published ... Jan 26 2019, 06:12 PM Olympic 914
:agree: They look great, that trick was published... Jan 26 2019, 08:45 PM 914forme
:agree: They look great, that trick was publishe... Jan 26 2019, 11:04 PM IronHillRestorations Bingo! That's what I call the "Upfix... Jan 26 2019, 09:04 PM windforfun I replaced my plastic rollers with metal ones. I ... Jan 27 2019, 11:23 AM second wind So......any chance of making a bunch of those nift... Jan 27 2019, 01:47 PM |
4 User(s) are reading this topic (4 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 22nd November 2024 - 06:24 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.