Floor Pan replacement, I should butt right? |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Floor Pan replacement, I should butt right? |
amfab |
Jun 1 2019, 05:40 PM
Post
#1
|
Member Group: Members Posts: 401 Joined: 17-May 16 From: Los Angeles Member No.: 20,004 Region Association: None |
I am fitting the RD front and rear floor pan pieces for replacement.
The front and rear overlap. I am assuming I should fit and trim and then butt weld them together. Would there be any reason to overlap and lap weld them? Thanks -Andrew |
IronHillRestorations |
Jun 1 2019, 09:04 PM
Post
#2
|
I. I. R. C. Group: Members Posts: 6,759 Joined: 18-March 03 From: West TN Member No.: 439 Region Association: None |
It depends on the car, and your skill level as a weldor. A driver quality car would be different than a high quality restoration.
If you don't have a true gas MIG, then don't even think about butt welding. If you try and butt weld with flux wire, you'll have weld inclusions and gnarly welds. A production body shop would typically want to do a lap joint. When you flange the panel you do add some stiffness, it's much easier to weld, and you have a little more margin of error fitting the pieces. For a pan, I'd want the overlap seam in the cabin, not visible under the car, or to let moisture in the lap seam. If you are a moderately skilled home welder with a good MIG (not flux coated) this is what I'd recommend. MIG welds are lower in tensile strength, and butt welding takes more skill. If you end up with any trouble with your butt welding you can have a much weaker joint that's more prone to crack. Part of it is where are you putting the lap joint and how critical is appearance vrs strength. MIG butt welds on body panels work better when you have a small uniform gap between the two panels, which can also make it easier to blow through. If you don't have a gap, you'll have more warpage. Whereas TIG is better if you're panels are perfectly butted together and you aren't filling the gap, which is virtually impossible on a large panel. This isn't to say you can't fill gaps with a TIG, it's just much harder than a wire feed MIG. The prince of welding technique is TIG, but it's very time consuming and technique oriented; not newbie friendly at all. Correct TIG welds are much stronger than MIG and have a higher tensile strength. Metal condition and cleanliness for TIG is several notches above what you can get away with on a MIG. A restoration shop with craftsmen would probably prefer to do a butt weld with TIG, but it takes alot more time, and even then in some cases not practical. The optimum filler rod for TIG on a floor pan would probably be .035 MIG wire I've been lucky with the few pans I've had to work on. The metal was good in the tunnel, and I used left and right pan sections, not the front/back pieces. The car was on a rotisserie, so it made it much easier and less welding out of position. I cut the bad pans off along the center of the weld nuggets along the flange for the tunnel, leaving a ledge to set the new pan on in the center, and then plug welded along the longitudinal. It took careful work with a cutoff wheel and carbide burrs to get the pans off, but it make for a very good repair. I'm a fair TIG weldor, but not competent enough, and not willing to fight any metal prep issues with an old lap flange, I used MIG. |
Lo-Fi Version | Time is now: 25th September 2024 - 10:43 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |