 Modify your front valance and bumper for GT cooler, Lets see some pics of your install and the bodywork. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Mark Henry |
 May 14 2021, 10:57 AM
Post
#1
|
|
that's what I do!  Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada  |
Hi I'd like to see how you dood it!
I just started hacking on my valance and I'm looking for inspiration. Attached image(s)  
|
   |
 
|
  |
Replies
| Shivers |
May 15 2021, 08:35 AM
Post
#2
|
|
Senior Member Group: Members Posts: 2,821 Joined: 19-October 20 From: La Quinta, CA Member No.: 24,781 Region Association: Southern California |
QUOTE(Mark Henry @ May 14 2021, 09:57 AM)  Hi I'd like to see how you dood it! I just started hacking on my valance and I'm looking for inspiration. I cut the hole 1/2" smaller than what I was shooting for.  I used hammers a slap and dollies to roll the metal over, trying to get a pressed factory look.  Then welded a plenum on for the finish. Gave it the break to follow the factory stiffening breaks.  Need to make it pretty now. Steel is real!  |
|
|
|
| mate914 |
May 15 2021, 09:37 AM
Post
#3
|
|
Matt Group: Members Posts: 799 Joined: 27-February 09 From: Eagles mere, PA Member No.: 10,102 Region Association: North East States 
|
QUOTE(Shivers @ May 15 2021, 10:35 AM) QUOTE(Mark Henry @ May 14 2021, 09:57 AM) Hi I'd like to see how you dood it! I just started hacking on my valance and I'm looking for inspiration. I cut the hole 1/2" smaller than what I was shooting for. I used hammers a slap and dollies to roll the metal over, trying to get a pressed factory look. Then welded a plenum on for the finish. Gave it the break to follow the factory stiffening breaks. Need to make it pretty now. Steel is real! I like that one. Simple and cost effective. I am doing this also and love the ideas. Matt |
|
|
|
Posts in this topic
Mark Henry Modify your front valance and bumper for GT cooler May 14 2021, 10:57 AM
VegasRacer :sawzall:
May 14 2021, 11:21 AM mepstein A member here Lazer cut the flat front piece then ... May 14 2021, 11:47 AM
wes
A member here Lazer cut the flat front piece then... May 14 2021, 12:14 PM
Mark Henry
A member here Lazer cut the flat front piece then... May 14 2021, 01:47 PM Marv's3.6six Here is mine. Front bumper one off fiberglass, low... May 14 2021, 12:04 PM mepstein @MB911 Ben might already have something in the wo... May 14 2021, 12:47 PM Justinp71 I just bought a front valance similar to yours but... May 14 2021, 01:27 PM Mark Henry
... one big opening and adding stainless square m... May 14 2021, 02:01 PM roblav1 Here's how I do the inside. Did it similar wi... May 14 2021, 02:03 PM wes I used the Material from an old damaged 914 engine... May 14 2021, 03:19 PM Mark Henry It's been a while since I did body work, right... May 14 2021, 05:34 PM rgalla9146 Started with a deep fiberglass Hershey find
C... May 14 2021, 05:36 PM mb911 I did mine out of steel and yes it looks great. If... May 15 2021, 06:19 AM mepstein I can’t seem to find the recent thread from the ... May 15 2021, 09:25 AM Shivers
I can’t seem to find the recent thread from the... May 15 2021, 09:39 AM mepstein
I can’t seem to find the recent thread from th... May 15 2021, 09:40 AM rgalla9146
[quote name='Shivers' post='2916019' date='May 15... May 15 2021, 09:52 AM mepstein
[quote name='Shivers' post='2916019' date='May 1... May 15 2021, 10:28 AM Shivers
[quote name='Shivers' post='2916019' date='May 15... May 15 2021, 10:36 AM Shivers
[quote name='Shivers' post='2916019' date='May 15... May 15 2021, 11:06 AM mb911
[quote name='Shivers' post='2916019' date='May 1... May 15 2021, 02:07 PM Shivers That came out real nice May 15 2021, 02:29 PM Mark Henry I'm not overly fond of the GT valance I mean i... May 15 2021, 04:56 PM Shivers
I'm not overly fond of the GT valance I mean ... May 15 2021, 05:07 PM live free & drive Below is a pic that you can read the contours of t... May 15 2021, 06:01 PM rgalla9146
Below is a pic that you can read the contours of ... May 16 2021, 05:44 AM iamchappy I made the opening about an 1 1/2 inches larger an... May 15 2021, 08:45 PM Mark Henry My valance so far....more of a pouting lip. ;)
I ... May 16 2021, 06:40 AM Mark Henry Another angle. May 16 2021, 06:47 AM Shivers That actually looks pretty good. May 16 2021, 07:01 AM |
10 User(s) are reading this topic (10 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 21st December 2024 - 11:19 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.