Boxster console |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Boxster console |
partwerks |
Sep 22 2021, 07:58 PM
Post
#1
|
Senior Member Group: Members Posts: 1,593 Joined: 7-September 06 From: Grand Island, NE Member No.: 6,787 |
Anyone have any pictures of what has been done for a console that works with the 6 speed Boxster setup?
If I use the Boxster console, looks like I would have to somehow patch in where the electricals were, and the handbrake. To get it to set back far enough, I would probably have to cut about 3" off the bottom of the center backpad, but then may not be able to open the console door, or take a section out of the length of the console. How easy is it to mend it back together and make it look like something? Also, will the factory rear sway bar, fit if using the 6 speed boxster trans? |
Gearup |
Sep 24 2021, 11:04 PM
Post
#2
|
Member Group: Members Posts: 160 Joined: 21-April 15 From: Denver Member No.: 18,660 Region Association: None |
Anyone have any pictures of what has been done for a console that works with the 6 speed Boxster setup? If I use the Boxster console, looks like I would have to somehow patch in where the electricals were, and the handbrake. To get it to set back far enough, I would probably have to cut about 3" off the bottom of the center backpad, but then may not be able to open the console door, or take a section out of the length of the console. How easy is it to mend it back together and make it look like something? Also, will the factory rear sway bar, fit if using the 6 speed boxster trans? Nice looking setup. Is that an LS with a holly intake? Are those Renegade adapter Parts? Brett |
partwerks |
Sep 25 2021, 09:41 PM
Post
#3
|
Senior Member Group: Members Posts: 1,593 Joined: 7-September 06 From: Grand Island, NE Member No.: 6,787 |
Anyone have any pictures of what has been done for a console that works with the 6 speed Boxster setup? If I use the Boxster console, looks like I would have to somehow patch in where the electricals were, and the handbrake. To get it to set back far enough, I would probably have to cut about 3" off the bottom of the center backpad, but then may not be able to open the console door, or take a section out of the length of the console. How easy is it to mend it back together and make it look like something? Also, will the factory rear sway bar, fit if using the 6 speed boxster trans? Nice looking setup. Is that an LS with a holly intake? Are those Renegade adapter Parts? Brett It's an LS3 with a hot cam. Holley intake, with 90 degree elbow. You have to use aftermarket fuel rails also. Otherwise you won't be able to close the casket lid. I got the adapter plate, clutch and pressure plate from Eric at: http://www.kitcarchassis.com/ Much easier on the pocket book. I think you can have the hole for an LS starter, or go with the one he sells with it. I got the motor mount bar and trans bracket from Renegade. I think I could have used my old motor mount bar, but wanted to make sure that it was sitting correctly so it would sit low enough, (the intake) since they have already pioneered the way. |
Lo-Fi Version | Time is now: 21st September 2024 - 06:59 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |