 Oil Breather Cover Lid, 901.107.701.3R |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
Model Specific Information
914/4: 70 71 72 73 74 75 76 914/6: 70 71 72
| DennisV |
 Sep 4 2022, 06:23 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 546 Joined: 8-August 20 From: Santa Rosa, CA Member No.: 24,575 Region Association: Northern California 
 |
Is this a correct Oil Cover Lid for a 1970 914-6? It appears to have a threaded port for a temperature or pressure sensor / switch. I can't find that part number in the 914 or early 911 parts catalogs.
901.107.701.3R  |
   |
 
|
  |
Replies
| sixnotfour |
Sep 9 2022, 10:57 AM
Post
#2
|
|
914 Wizard Group: Members Posts: 10,636 Joined: 12-September 04 From: Life Elevated..planet UT. Member No.: 2,744 Region Association: Rocky Mountains 
|
TVP was annoying, pull up to stop light with high idle to burn off left over fuel .... not Cool , but.. the beginning of emissions...probably better than an air pump..
|
|
|
|
Posts in this topic
DennisV Oil Breather Cover Lid Sep 4 2022, 06:23 PM
rgalla9146
Is this a correct Oil Cover Lid for a 1970 914-6?... Sep 5 2022, 05:59 AM nditiz1 I thought all 6s were carbd which would mean no TP... Sep 5 2022, 06:36 AM SixerJ My -6 engine which happens to be on the floor at t... Sep 5 2022, 07:50 AM johnhora The "TPS" was used as an early emissions... Sep 5 2022, 08:10 AM rgalla9146 Original equipment on our cars was a temp sensor ... Sep 5 2022, 08:18 AM johnhora 914-6 Throttle Valve Positioner....the vacuum ... Sep 5 2022, 08:33 AM johnhora 914-6 intake manifold with vacuum ports
pictur... Sep 5 2022, 08:39 AM
DennisV
914-6 intake manifold with vacuum ports
Very int... Sep 9 2022, 10:09 AM rgalla9146
[quote name='johnhora' post='3027284' date='Sep 5... Sep 9 2022, 01:49 PM DennisV
Dennis those carbs and manifolds are from a ... Sep 9 2022, 04:12 PM DennisV
Dennis those carbs and manifolds are from a ... May 29 2024, 10:14 AM davep You are confusing casting numbers with part #... Sep 5 2022, 08:43 AM rgalla9146 Holy Cow Visual aids aplenty Sep 5 2022, 01:10 PM fixer34 Had me curious so I went to look. March '70. ... Sep 9 2022, 12:20 PM fixer34 I have wondered for a while what the sensor was th... Sep 9 2022, 12:27 PM rgalla9146 I think that switch (two wire) was the trigger for... Sep 9 2022, 01:30 PM |
5 User(s) are reading this topic (5 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 24th November 2024 - 10:35 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.