 Tell me about oil cooler seals |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| emerygt350 |
 May 31 2023, 06:10 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 2,473 Joined: 20-July 21 From: Upstate, NY Member No.: 25,740 Region Association: North East States  |
I thought my leak to the front of 4 was the valve cover gasket. Now I am leaning more towards the seal on the oil cooler. Seems to only really leak when the oil is hot.
|
   |
 
|
  |
Replies
| brant |
Jun 2 2023, 04:10 PM
Post
#2
|
|
914 Wizard Group: Members Posts: 11,771 Joined: 30-December 02 From: Colorado Member No.: 47 Region Association: Rocky Mountains 
|
Also a small leaker blows around a lot in that area
It’s existing hot air and swirls some too I have an oil pump minor leak that looks like most of the same areas as your pics But it gets around in that air path I’ll pull the motor eventually but living with it until then It’s my street car and runs great so I’ve been putting it off Wash everything I even tape (aluminum tape not duct tape) some folded paper towel into strategic areas …. Test warm one time and not any longer than needed See which area it’s coming from…. If not multiples |
 |
|
Posts in this topic
emerygt350 Tell me about oil cooler seals May 31 2023, 06:10 PM
Chaznaster I think I had the same leak. Replaced the seals wi... May 31 2023, 06:48 PM
emerygt350
I think I had the same leak. Replaced the seals w... May 31 2023, 08:55 PM emerygt350 Very interesting indeed, has anyone else attempted... May 31 2023, 09:04 PM r_towle On jack stands, it can be done.
I put Vaseline on ... May 31 2023, 10:01 PM emerygt350 Awesome. Did you drain the oil? Jun 1 2023, 03:28 AM Jack Standz Have done it a couple times. The thread shows yo... Jun 1 2023, 07:48 AM ctc911ctc I did it on jack stands once - it was a PAIN!... Jun 1 2023, 01:48 PM brant its easier to remove the engine.
if you choose no... Jun 1 2023, 01:54 PM ClayPerrine
if you choose not to remove the engine.... one tr... Jun 2 2023, 06:16 AM brant
if you choose not to remove the engine.... one t... Jun 2 2023, 08:32 AM r_towle I have done it on jack stands...its not terribly h... Jun 1 2023, 02:04 PM emerygt350 I was going to ask about the tubes. Thanks rich. ... Jun 1 2023, 03:45 PM iankarr
I was going to ask about the tubes. Thanks rich.... Jun 1 2023, 06:22 PM Shivers Have you changed the oil and filter lately?
Some ... Jun 1 2023, 03:56 PM emerygt350 It's a mobile1. I will definitely check and se... Jun 1 2023, 05:02 PM 914werke
I did it on jack stands once - it was a PAIN... Jun 1 2023, 06:27 PM r_towle Unless you have an engine stand, and a way to pick... Jun 1 2023, 06:40 PM brant I’ll just add that it’s very satisfying to dro... Jun 1 2023, 07:21 PM bkrantz Another vote for dropping the engine. Lots of thi... Jun 1 2023, 07:41 PM Superhawk996 Try to do it without removing the motor.
That way... Jun 2 2023, 06:26 AM emerygt350 Ok, I have started investigating.
One question, h... Jun 2 2023, 10:45 AM emerygt350 Notice how nice and dry the other side is.
No ide... Jun 2 2023, 10:48 AM Superhawk996
Notice how nice and dry the other side is.
No id... Jun 2 2023, 04:08 PM Superhawk996
No idea why that hose clamp is in the heater pip... Jun 2 2023, 04:12 PM emerygt350 The filter was on good. Not that it means much. ... Jun 2 2023, 11:14 AM brant It’s hard to guess where your leak is
Could be ... Jun 2 2023, 03:13 PM Superhawk996
It’s hard to guess where your leak is
Could be... Jun 2 2023, 03:36 PM emerygt350 I completely understand that all of this will be e... Jun 2 2023, 03:48 PM Superhawk996 Just to be clear I’m not making fun of you. I l... Jun 2 2023, 04:00 PM brant Probably 100 times I’ve dropped 914 motors with ... Jun 2 2023, 04:02 PM Superhawk996 I’m also a fan of UV dye in the oil approach.
... Jun 2 2023, 04:17 PM emerygt350 I have not looked at the pump. Wouldn't that ... Jun 2 2023, 04:27 PM emerygt350 The hot engine thing keeps pulling me back to the ... Jun 2 2023, 04:29 PM emerygt350 And don't get me wrong, as soon as I see the n... Jun 2 2023, 04:30 PM r_towle When was the last time you changed the valve cover... Jun 2 2023, 06:46 PM emerygt350 Two days ago. Sadly. That was my first impulse. ... Jun 2 2023, 07:20 PM emerygt350 And the ones I replaced are from last fall when I ... Jun 2 2023, 07:21 PM mate914 You did just run at the Glen... Maybe high RPM... Jun 2 2023, 07:59 PM emerygt350 I think that did occur up top. But now even regul... Jun 3 2023, 05:49 AM rhodyguy Start spraying ALL of the ducting fasteners with a... Jun 4 2023, 11:27 AM emerygt350 Well... replaced the seals with the engine in. I... Jun 19 2023, 01:47 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 31st October 2024 - 08:19 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.