 2.0 Head Gasket delete? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| torakki |
 Jun 15 2024, 11:10 AM
Post
#1
|
|
Member  Group: Members Posts: 55 Joined: 5-October 18 From: Nor Cal Member No.: 22,545 Region Association: Northern California  |
I've read where it's a good idea to remove the head gaskets and re-assemble without them. Something about, they crush and cause an issue. Is there anything else you need to do or change, in their place? Like a different head design?
Thanks |
   |
 
|
  |
Replies
| emerygt350 |
Jun 16 2024, 02:48 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,532 Joined: 20-July 21 From: Upstate, NY Member No.: 25,740 Region Association: North East States |
Is it still injected? D-jet? I would be looking to the mps if I were running rich
A shot diaphragm produces a rich condition. Air leaks don't do anything but raise the idle. |
|
|
|
Posts in this topic
torakki 2.0 Head Gasket delete? Jun 15 2024, 11:10 AM
914Sixer If you leave them out, lap your barrels in. Jun 15 2024, 11:37 AM rick 918-S Just be sure the head mating surfaces are true and... Jun 15 2024, 11:38 AM technicalninja Check deck height!
The upper surface of the p... Jun 15 2024, 12:18 PM ClayPerrine Ok... I am going to climb up on my soapbox here...... Jun 15 2024, 02:16 PM 930cabman I built my 2056 a couple years ago (still running ... Jun 15 2024, 02:52 PM
ClayPerrine
I do recall reading the factory recommended to e... Jun 15 2024, 03:21 PM 930cabman
I do recall reading the factory recommended to ... Jun 15 2024, 04:15 PM rick 918-S Since Clay responded I need to clarify my post. St... Jun 15 2024, 03:11 PM technicalninja
Ok... I am going to climb up on my soapbox here..... Jun 15 2024, 03:18 PM ClayPerrine
P.S. [b]@[url=http://www.914world.com/bbs2/index... Jun 15 2024, 03:25 PM emerygt350 I kept them out of my 2056 build. I ended up only... Jun 15 2024, 03:19 PM torakki OK, way more responses than I thought and way more... Jun 16 2024, 02:12 PM 930cabman
OK, way more responses than I thought and way mor... Jun 16 2024, 05:27 PM 914werke All it took for me was one engine tear down exposi... Jun 16 2024, 03:49 PM ClayPerrine
(& blessed by the manufacture)
I still ... Jun 16 2024, 08:41 PM r_towle I don’t believe a leak at the head/cylinder woul... Jun 16 2024, 04:36 PM r_towle This site may help if diagnosing djet
https://mem... Jun 16 2024, 04:38 PM emerygt350 I don't think the two are associated (I don... Jun 16 2024, 05:47 PM 914Sixer I used the gasket on my 2056. Jun 16 2024, 07:08 PM emerygt350
I've read where it's a good idea to remov... Jun 17 2024, 05:36 AM ClayPerrine
[quote name='torakki' post='3151083' date='Jun 15... Jun 17 2024, 09:05 AM emerygt350 Dbl post Jun 17 2024, 05:37 AM 914werke [quote name='emerygt350' post='3151350' date='Jun... Jun 17 2024, 11:04 AM 914werke (& blessed by the manufacture) I still wan... Jun 17 2024, 11:12 AM ClayPerrine Look. . this is real simple. Do what you want wi... Jun 17 2024, 11:34 AM Nogoodwithusernames Pardon my lack of knowledge in this area, but what... Jun 17 2024, 11:52 AM mmichalik :popcorn: Jun 17 2024, 12:35 PM 930cabman Possible/probable the folks at Porsche never had a... Jun 17 2024, 01:39 PM thomasotten Not wanting to enter a debate that clearly needs a... Jun 17 2024, 06:39 PM Al Meredith I stayed up last night reading a bunch of articles... Jun 18 2024, 10:57 AM Jake Raby
I stayed up last night reading a bunch of article... Jun 30 2024, 10:08 AM ClayPerrine
I stayed up last night reading a bunch of articl... Jun 30 2024, 05:15 PM emerygt350
[quote name='Jake Raby' post='3153973' date='Jun ... Jun 30 2024, 05:43 PM 914werke BTW #5 should be performed on ALL T4 builds (usin... Jun 18 2024, 12:11 PM 930cabman
BTW #5 should be performed on ALL T4 builds (usi... Jun 18 2024, 12:17 PM 914werke correct. Poor mans oil squirter! Jun 18 2024, 12:18 PM rick 918-S Question:
The update states improvements were mad... Jul 2 2024, 06:54 AM Superhawk996
Question:
The update states improvements were ma... Jul 2 2024, 07:22 AM rick 918-S
Question:
The update states improvements were m... Jul 2 2024, 09:05 PM Superhawk996
Type IV rods can be notched, Cylinders can be h... Jul 2 2024, 09:57 PM Nogoodwithusernames Some various ponderings on this topic.
-So we hav... Jul 2 2024, 09:29 AM 930cabman
Some various ponderings on this topic.
-So we ha... Jul 2 2024, 05:09 PM wonkipop
Some various ponderings on this topic.
-So we ha... Jul 2 2024, 05:28 PM 930cabman :agree:
All of us need to thank Jake for his gen... Jul 3 2024, 10:44 AM Jake Raby This isn't about choosing sides.
I can't b... Jul 4 2024, 01:30 PM |
21 User(s) are reading this topic (21 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 7th January 2025 - 09:43 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.