 Cosmetic rubber interior windshield trim, How to install? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| drmitch |
 Dec 3 2024, 10:21 AM
Post
#1
|
|
Newbie  Group: Members Posts: 38 Joined: 7-October 13 From: So California Member No.: 16,485 Region Association: Southern California  |
Good morning,
I've purchased a replacement interior cosmetic rubber seal that goes along the bottom of the windshield. I'm told that it's a simple installation, not requiring the removal of the windshield or dash, and perhaps a thirty-minute project. THAT SAID...I'd love to get a step by step account of how to do it, rather than figure it out by trial and error. Tips on getting the old, cracked seal out? Tips on getting the new seal seated and centered? SMC's site says "It is installed by cutting the ends so the seal is slightly longer and over-centering it." I have no idea what that means. Any shared experience would be appreciated. Thanks. Mitch |
   |
 
|
  |
Replies
| FlacaProductions |
Dec 3 2024, 05:32 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,829 Joined: 24-November 17 From: LA Member No.: 21,628 Region Association: Southern California 
|
ok - so yeah. I'd make sure all of the old remnants are gone.
|
|
|
|
Posts in this topic
drmitch Cosmetic rubber interior windshield trim Dec 3 2024, 10:21 AM
hndyhrr
Good morning,
I've purchased a replacement i... Dec 3 2024, 10:58 AM
drmitch
Good morning,
I've purchased a replacement ... Dec 3 2024, 10:59 AM Chris914n6 Removal- if yours is like mine was it's hard, ... Dec 3 2024, 11:43 AM drmitch
Removal- if yours is like mine was it's hard,... Dec 3 2024, 12:50 PM SirAndy There's no glue or sealant required, correct?... Dec 3 2024, 01:39 PM mb911
There's no glue or sealant required, correct... Dec 3 2024, 02:32 PM SirAndy Did you find a source for units that have the meta... Dec 3 2024, 02:34 PM SirAndy
[quote name='mb911' post='3180046' date='Dec 3 20... Dec 3 2024, 02:39 PM drmitch
Removal- if yours is like mine was it's hard,... Dec 3 2024, 03:39 PM SirAndy The metal "backbone" remains, after digg... Dec 3 2024, 03:44 PM drmitch
The metal "backbone" remains, after dig... Dec 3 2024, 04:07 PM SirAndy
914Rubber's description: New reproduction of ... Dec 3 2024, 04:13 PM drmitch
Removal- if yours is like mine was it's hard,... Dec 3 2024, 03:40 PM FlacaProductions When you're doing this, if you'd be so kin... Dec 3 2024, 01:10 PM drmitch
When you're doing this, if you'd be so ki... Dec 3 2024, 02:23 PM sbsix The alternative is to take your dash out. I replac... Dec 3 2024, 02:27 PM FlacaProductions I would think that the "backbone" also c... Dec 3 2024, 03:45 PM drmitch OK, that wasn't so bad. Project is finished. ... Dec 3 2024, 05:44 PM 914sgofast2 On my 1970 model year, I removed the old crusty se... Dec 3 2024, 06:08 PM drmitch
On my 1970 model year, I removed the old crusty s... Dec 3 2024, 07:24 PM FlacaProductions Certainly looks like an improvement to me! Dec 3 2024, 06:08 PM drmitch Thanks for the help, everyone. Next project might... Dec 3 2024, 08:36 PM |
3 User(s) are reading this topic (3 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 12th December 2024 - 09:35 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.