 916 chassis |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Montreal914 |
 Feb 1 2025, 06:08 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,772 Joined: 8-August 10 From: Claremont, CA Member No.: 12,023 Region Association: Southern California 
 |
Were the few 916's equipped with the GT stiffening kit?
Other than the obvious rigid roof, were there any chassis stiffening improvement to handle the larger powertrain/gearbox? |
   |
 
|
  |
Replies
| TMM914 |
Feb 1 2025, 08:36 PM
Post
#2
|
|
Member Group: Members Posts: 50 Joined: 1-January 20 From: St Jacobs Ontario Canada Member No.: 23,786 Region Association: Canada
|
Here is a shot of the 916 at Canepa that you can see the reinforcement plates present.
My guess is they were installed by the factory.  |
|
|
|
| dr914@autoatlanta.com |
Feb 3 2025, 05:57 PM
Post
#3
|
|
914 Guru Group: Members Posts: 8,134 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
funny the transmission round plates are on the wrong side of the ears
916 had the chassis stiffening kit welded in QUOTE(TMM914 @ Feb 1 2025, 07:36 PM)  Here is a shot of the 916 at Canepa that you can see the reinforcement plates present. My guess is they were installed by the factory. |
|
|
|
Posts in this topic
Montreal914 916 chassis Feb 1 2025, 06:08 PM
rgalla9146 [quote name='dr914@autoatlanta.com' post=... Feb 3 2025, 08:11 PM
Maltese Falcon For some reason those cup washers /transaxle mount... Feb 1 2025, 08:44 PM davep
But I think that with the 916 hot rod 2.4 mfi, th... Feb 2 2025, 08:21 PM TMM914
But I think that with the 916 hot rod 2.4 mfi, t... Feb 3 2025, 03:27 PM Maltese Falcon This is how the 916 nose cone transaxle mounting h... Feb 1 2025, 09:17 PM rgalla9146
This is how the 916 nose cone transaxle mounting ... Feb 2 2025, 08:09 AM Maltese Falcon
This is how the 916 nose cone transaxle mounting... Feb 2 2025, 10:08 AM Maltese Falcon @Montreal if you have a bit of time during your 4 ... Feb 2 2025, 11:16 PM Maltese Falcon Master exhaust header fabricator Eujeñio was so p... Feb 2 2025, 11:21 PM Maltese Falcon Good times at this track, just needed a taller 5th... Feb 2 2025, 11:26 PM burton73 Here are several photos of the reinforcement that ... Feb 3 2025, 09:07 AM Montreal914 Thank you TMM914, Marty, Rory, Dave, and Bob. B:)... Feb 3 2025, 09:39 AM 930cabman These chassis mods (meant to stiffen) are great, b... Feb 3 2025, 10:27 AM technicalninja
Thank you TMM914, Marty, Rory, Dave, and Bob. B:... Feb 3 2025, 11:01 AM Maltese Falcon @Montreal914 you can always come by* + visit the... Feb 3 2025, 11:18 AM davep OH, 9141430195 is Brutus, the prototype, so, close... Feb 3 2025, 04:03 PM Cairo94507 I really went back and forth on stiffening modific... Feb 3 2025, 05:21 PM ClayPerrine I was always under the impression the big cupped w... Feb 4 2025, 07:12 AM Montreal914 So it looks like the concensus on the 916 is:
- W... Feb 4 2025, 09:19 AM |
16 User(s) are reading this topic (16 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 5th February 2025 - 07:03 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.