 End Play, It don't move |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Allan |
 Feb 27 2005, 09:26 PM
Post
#1
|
|
Teenerless Weenie  Group: Members Posts: 8,373 Joined: 5-July 04 From: Western Mesopotamia Member No.: 2,304 Region Association: Southern California  |
I finally got my son over to help me set my crank end play. Bolted up the flywheel with the original shims under it and for the life of me we can't get the crank to slide at all. I'm pretty sure that it is supposed to be .003-.005. What is the best way to push and pull to get it to move?
Thanks |
   |
 
|
  |
Replies
| Allan |
Feb 28 2005, 08:48 PM
Post
#2
|
|
Teenerless Weenie Group: Members Posts: 8,373 Joined: 5-July 04 From: Western Mesopotamia Member No.: 2,304 Region Association: Southern California |
Okay, I'm back at it again. I put the 2 larger shims in and ended up with .010 of end play. I added the third shim which measures as best that my crappy calipers can tell around .005. When I measure again I get right about .0045, BUT, I have to push on the flywheel to get that. When I let go it will go back to zero. Should I have to put pressure on the flywheel to get the reading?
P.S. Tried to call ya Joe but you no home. |
|
|
|
Posts in this topic
Headrage End Play Feb 27 2005, 09:26 PM
Bleyseng Do you have the proper tools to set it? It doesn... Feb 27 2005, 10:01 PM Demick Remove all the shims, bolt up the flywheel, and me... Feb 27 2005, 10:05 PM Headrage ... Feb 27 2005, 10:13 PM Joe Sharp Allan. you need .004, anything less is unaccetable... Feb 27 2005, 10:14 PM Headrage Thanks Joe. I'm gonna hang it up for tonight.... Feb 27 2005, 10:17 PM SLITS Hey Allan, the barbarian here....when I setup end ... Feb 28 2005, 09:27 PM r_towle i was gonna say a rubber mallet,,,but i figured i ... Feb 28 2005, 09:38 PM SLITS <... Feb 28 2005, 09:41 PM Headrage Okay, using the brute force method, it looks to be... Feb 28 2005, 09:44 PM r_towle to small Feb 28 2005, 09:47 PM r_towle gentle.....i use a rubber mallet....slits said sof... Feb 28 2005, 09:48 PM Headrage Well I can get .005 if I just push on it a little ... Feb 28 2005, 09:52 PM r_towle that would depend on what you did to the case, cra... Feb 28 2005, 09:57 PM Headrage I had the case align bored and the crank polished.... Feb 28 2005, 10:04 PM SLITS The case work would probably have more to do with ... Feb 28 2005, 10:42 PM Headrage Well I'm going to leave it alone for tonight a... Feb 28 2005, 10:45 PM Joe Sharp Allan: If the crank is moving after you put in all... Feb 28 2005, 10:49 PM Headrage Okay, let's try this again. I went to the loc... Mar 1 2005, 04:31 PM SLITS <... Mar 1 2005, 05:20 PM
Headrage Oh I've got that covered. Fuel lines going in... Mar 1 2005, 05:39 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 31st October 2024 - 07:30 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.