 Clutch Tube Repair, Step by Step Pictures |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| ThinAir |
 Mar 30 2005, 10:22 PM
Post
#1
|
|
Best friends  Group: Members Posts: 2,560 Joined: 4-February 03 From: Flagstaff, AZ Member No.: 231 Region Association: Southwest Region 
 |
This is the center tunnel from the donor car, turned upside down.
Attached thumbnail(s) 
|
   |
 
|
  |
Replies
| ThinAir |
Mar 30 2005, 10:41 PM
Post
#2
|
|
Best friends Group: Members Posts: 2,560 Joined: 4-February 03 From: Flagstaff, AZ Member No.: 231 Region Association: Southwest Region
|
Mike was not happy with the way the welding came out. I'm sure it will hold just fine. It looks better after I worked on it with the grinder. It's hard to reach a lot of places in that space. Once it is painted it will look just fine by me.
Attached image(s) 
|
|
|
|
Posts in this topic
ThinAir914 Clutch Tube Repair Mar 30 2005, 10:22 PM
ThinAir914 This is what the center weld point looks like. Th... Mar 30 2005, 10:24 PM ThinAir914 This is the firewall from the donor to show what i... Mar 30 2005, 10:25 PM ThinAir914 This is what our firewall looked like. We were su... Mar 30 2005, 10:28 PM ThinAir914 The front end of our clutch tube. Mar 30 2005, 10:30 PM ThinAir914 The front tube bracket reinforced. Mar 30 2005, 10:30 PM ThinAir914 Front tube bracket #2. The brazing that you see c... Mar 30 2005, 10:31 PM ThinAir914 This is the flap we cut in the front of the tunnel... Mar 30 2005, 10:32 PM ThinAir914 This is the rear flap, measured from the cross bra... Mar 30 2005, 10:33 PM ThinAir914 The front bracket as originally repaired. We just... Mar 30 2005, 10:35 PM ThinAir914 We cut a piece from the donor's old tunnel to ... Mar 30 2005, 10:36 PM ThinAir914 The center weld after it was finished. You can see... Mar 30 2005, 10:37 PM ThinAir914 The firewall was repaired by bending the metal bac... Mar 30 2005, 10:39 PM ThinAir914 The finished firewall welding. Mar 30 2005, 10:40 PM ThinAir914 The engine end of our tube was bent and out of rou... Mar 30 2005, 10:45 PM ThinAir914 My welder at work. I can't say thanks enough ... Mar 30 2005, 10:46 PM ThinAir914 It was only 44F and the wind was blowing when we d... Mar 30 2005, 10:48 PM ThinAir914 As clutch cable tube repair jobs go, I would guess... Mar 30 2005, 10:50 PM mattillac nice work! Mar 31 2005, 12:34 AM Jeff Bowlsby Thanks Ernie...nice job. Kinda makes you wish the... Mar 31 2005, 01:02 AM Mike9142.0 The picks make my welds look good Oct 7 2005, 12:14 PM SirAndy Oct 7 2005, 12:22 PM McMark Nice Job!
As you noticed, you have to be care... Oct 7 2005, 12:43 PM jonwatts I like that washer on the rear firewall. I might d... Oct 7 2005, 12:59 PM Spoke Oct 7 2005, 12:59 PM jonwatts I think he means don't burn through and block ... Oct 7 2005, 01:20 PM Brad Roberts Correct Jon. I slide a number 2 Phillips into the ... Oct 7 2005, 03:22 PM McMark Welding can something like what is pictured below.... Oct 7 2005, 03:43 PM bondo Oct 7 2005, 04:13 PM ThinAir914 Oct 8 2005, 11:23 AM bd1308 i guess
metal ready converts rust into a paintabl... Oct 8 2005, 11:33 AM SirAndy Oct 12 2005, 07:56 PM SirAndy Oct 15 2005, 01:22 PM
malcolm2 Sorry.... old post, but a good one. Wanted to add... Mar 13 2023, 01:41 PM |
11 User(s) are reading this topic (11 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 7th April 2025 - 09:53 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.