 Carb questions, any guru carb guys? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| merrill |
 Aug 12 2005, 03:59 PM
Post
#1
|
|
Dirt Pimp  Group: Members Posts: 224 Joined: 25-January 05 From: Tahoe City, Ca Member No.: 3,505 Region Association: None  |
My carbed 2.0 is idleing very high (2000-2400) when it warms up (IMG:http://www.914world.com/bbs2/html/emoticons/huh.gif) I can tap the throttle and it will drop to 1900, but I would like to adjust it lower. Where do I look for the warm idle adjustment?
It has been popping a bit too, so I got a pertronix that I need to install with the hope that it is points? any feedback is welcome, as well as harassment. |
   |
 
|
  |
Replies
| rhodyguy |
Aug 12 2005, 09:05 PM
Post
#2
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,116 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
back one side off pretty well(idle adj screw). then turn the idle down with the other. then readjust the loose one just to the point of the idle increasing again. with the engine off, open the butterflys (with the linkage cross bar) and let it close on it's own. it should snap back with authority. a weak spring sometimes will be overcome by the vaccum and the plates will open a bit. "poping" out the exhaust or "sneezing" back through the carbs?
k |
|
|
|
Posts in this topic
merrill Carb questions Aug 12 2005, 03:59 PM
lapuwali Which carb or carbs? Single progressive Weber? D... Aug 12 2005, 04:24 PM merrill Doohhh! Dual carb webber 44 idf. Aug 12 2005, 04:34 PM lapuwali K. Those have throttle stop screws holding the th... Aug 12 2005, 04:41 PM merrill Thanks James http://www.914wo... Aug 12 2005, 04:51 PM maf914 If you don't have a Weber manual, I'd reco... Aug 13 2005, 07:13 AM merrill Rhody Guy, I am not sure about the sneezing. I se... Aug 13 2005, 11:31 AM r_towle check your valve adjustments. poorly adjusted valv... Aug 13 2005, 12:55 PM BGman Merrill, don't mean to hijack your thread...
... Aug 13 2005, 01:12 PM r_towle what size mains, what size venturis???
Rich Aug 13 2005, 01:17 PM merrill Thanks for the feedback Rich. I will not be able ... Aug 13 2005, 05:13 PM r_towle Aug 13 2005, 05:24 PM SirAndy Aug 13 2005, 05:38 PM r_towle I was successful at tuning it out of a beetle with... Aug 13 2005, 05:44 PM BGman Don't know about cam specs- but I do have an o... Aug 13 2005, 09:34 PM
9146986 Is this a new engine? Did it just develop this pr... Aug 14 2005, 10:46 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 26th June 2024 - 07:27 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.