 Mega Jolt Light Junior thread for a /6, Because folks have asked |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Dr Evil |
 Jun 2 2006, 08:41 PM
Post
#1
|
|
Send me your transmission!  Group: Members Posts: 23,034 Joined: 21-November 03 From: Loveland, OH 45140 Member No.: 1,372 Region Association: MidAtlantic Region 
 |
So I made mention of my MJLJ in a few threads as of late which has seemed to generate some interest in my build/progress (?).
A little back ground on me: I have over 10 years of electronics/electrical trouble shooting and assemblyexperience form both high school, and the Coast Guard where I was an Avionics Technician. This is why I had no problem assembling the MJLJ unit. However, I am not a computer guy and programming is proving to be a HUGE PITA. The build: MJLJ uses EDIS which is a Ford distributorless electronic ignition system. The information for this part is available at http://picasso.org/mjlj/ To use the unit you will need a 36-1 toothed gear for the crank and a VR sensor. I am including pics of my pieces. Here would be a good place to show your prowess in programming as I am lost. it seems that my USB--> serial adaptor is not working, or it could be the unit. More to come. Post pics here for discussion. Pics are of the toothed gear installed and of the pully with it mounted separate. Attached thumbnail(s)  Attached image(s)  
|
   |
 
|
  |
Replies
| Dr Evil |
Jun 2 2006, 11:08 PM
Post
#2
|
|
Send me your transmission! Group: Members Posts: 23,034 Joined: 21-November 03 From: Loveland, OH 45140 Member No.: 1,372 Region Association: MidAtlantic Region
|
Ya, I have no provision on the V2 board for TB pick up. I woudl just use the vacuum tap off of the TB that usually goes to the advance for my set up.
USB--->Serial issues: You are correct, Sir. There have been issues with adaptors. Some work, others do not and no one knows why. There are several threads on this topic on the posted site above if you just search "USB". Tonight I used hyperterminal to check my MJLJ and I believe it has shown me that my adaptor is not working. I will attempt to track down a serial cable tomarrow and use my desk top. Hopefully I will have better results. Question: I need to set the timing curve to my cams, correct? I have SC cams in my engine instead of the stock CIS cams from a '74. This is only made more confusing due to the small bit of advance that the SC curve below shows. The others are like 30 deg + I am attaching some tables for others to use should they want to do this as well. Attached image(s)   
|
|
|
|
Posts in this topic
Dr Evil Mega Jolt Light Junior thread for a /6 Jun 2 2006, 08:41 PM
Dr Evil Here is a pic of my assembled unit, it is a V2 boa... Jun 2 2006, 08:50 PM lapuwali A lot of people in MS land have had a lot of troub... Jun 2 2006, 08:53 PM TimT You may have a problem getting a good MAP signal i... Jun 2 2006, 09:12 PM Aaron Cox mike has CIS, so i assume single TB Jun 2 2006, 09:14 PM
TimT QUOTE
Dr Evil I will be getting a vacuum gauge from some where t... Jun 2 2006, 11:11 PM TimT You can use the curves you posted as a starting po... Jun 2 2006, 11:52 PM Dr Evil Good observation, Tim. I did not notice those thin... Jun 3 2006, 12:18 AM DNHunt Dr. Evil
I'm not sure how much this will help... Jun 3 2006, 08:59 AM Dr Evil Dr. Dave, I am always appreciative of any info. I ... Jun 3 2006, 10:15 AM DNHunt QUOTE
Dr Evil Luckily I left the jumper plug in my harness so I ... Aug 12 2006, 10:40 AM |
5 User(s) are reading this topic (5 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 27th December 2024 - 07:50 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.