 Mega Jolt Light Junior thread for a /6, Because folks have asked |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Dr Evil |
 Jun 2 2006, 08:41 PM
Post
#1
|
|
Send me your transmission!  Group: Members Posts: 23,034 Joined: 21-November 03 From: Loveland, OH 45140 Member No.: 1,372 Region Association: MidAtlantic Region 
 |
So I made mention of my MJLJ in a few threads as of late which has seemed to generate some interest in my build/progress (?).
A little back ground on me: I have over 10 years of electronics/electrical trouble shooting and assemblyexperience form both high school, and the Coast Guard where I was an Avionics Technician. This is why I had no problem assembling the MJLJ unit. However, I am not a computer guy and programming is proving to be a HUGE PITA. The build: MJLJ uses EDIS which is a Ford distributorless electronic ignition system. The information for this part is available at http://picasso.org/mjlj/ To use the unit you will need a 36-1 toothed gear for the crank and a VR sensor. I am including pics of my pieces. Here would be a good place to show your prowess in programming as I am lost. it seems that my USB--> serial adaptor is not working, or it could be the unit. More to come. Post pics here for discussion. Pics are of the toothed gear installed and of the pully with it mounted separate. Attached thumbnail(s)  Attached image(s)  
|
   |
 
|
  |
Replies
| Dr Evil |
Aug 12 2006, 10:40 AM
Post
#2
|
|
Send me your transmission! Group: Members Posts: 23,034 Joined: 21-November 03 From: Loveland, OH 45140 Member No.: 1,372 Region Association: MidAtlantic Region
|
Luckily I left the jumper plug in my harness so I can just pull it and cause it to go to default. I can try this. As for the VR wires, I matched blue-blue, and grey-grey. Pretty sure its not that, but I realy can not be sure of anything as it is not running at all.
An odd thing was that I had to switch where I thought coil 2 and 3 were ont he pack so that now it goes coil 1 - 3 - 2. Before this it would try to stop my engine in mid stroke....not nice. |
|
|
|
Posts in this topic
Dr Evil Mega Jolt Light Junior thread for a /6 Jun 2 2006, 08:41 PM
Dr Evil Here is a pic of my assembled unit, it is a V2 boa... Jun 2 2006, 08:50 PM lapuwali A lot of people in MS land have had a lot of troub... Jun 2 2006, 08:53 PM TimT You may have a problem getting a good MAP signal i... Jun 2 2006, 09:12 PM Aaron Cox mike has CIS, so i assume single TB Jun 2 2006, 09:14 PM
TimT QUOTE
Dr Evil Ya, I have no provision on the V2 board for TB pic... Jun 2 2006, 11:08 PM Dr Evil I will be getting a vacuum gauge from some where t... Jun 2 2006, 11:11 PM TimT You can use the curves you posted as a starting po... Jun 2 2006, 11:52 PM Dr Evil Good observation, Tim. I did not notice those thin... Jun 3 2006, 12:18 AM DNHunt Dr. Evil
I'm not sure how much this will help... Jun 3 2006, 08:59 AM Dr Evil Dr. Dave, I am always appreciative of any info. I ... Jun 3 2006, 10:15 AM DNHunt QUOTE
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 27th December 2024 - 02:45 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.