 Winter Projects...., How is everyone doing? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jr91472 |
  Dec 27 2006, 08:57 AM
Post
#1
|
|
"I'm pacing myself sergeant..."  Group: Members Posts: 1,205 Joined: 2-August 04 From: McKinney, TX Member No.: 2,437  |
I have been on a roll since Dec 1:
-new clutch, p-plate, and lightened flywheel -changed tranny oil -changed motor oil + filter -adjusted valves -fixed my speedo -replaced roll bar and targa top weather seals (thanks Santa) -got new floor mats (thanks Santa) -installed new dash face material (see pic) Still to do: -new brake pads + flush -install new ball joints good times (IMG:style_emoticons/default/biggrin.gif) Attached image(s) 
|
   |
 
|
  |
Replies
| RON S. |
Dec 27 2006, 12:46 PM
Post
#2
|
|
9140430841, FINALLY RUNNING Group: Members Posts: 1,212 Joined: 22-May 03 From: WALTERBORO,S.C. Member No.: 724 Region Association: South East States |
I'm gonna get my 930 front brakes installed by next weekend.That'll do it for me. Ron |
|
|
|
| nocones |
Dec 27 2006, 01:45 PM
Post
#3
|
|
Sportscar lunatic Group: Members Posts: 428 Joined: 17-June 04 From: Santa Rosa, CA Member No.: 2,220 |
Like Chappy said, spring/summer project has drifted through fall and into winter.
I have accumulated a lot of parts though. Honestly if I can find some time I can bolt the flywheel and new clutch assembly in anytime. Still need to inspect the 915 while it's out and replace the seal on the shift shaft. That would get the car back on the road at least. (IMG:style_emoticons/default/driving.gif) Other projects like installing the new struts and brakes, longer wheel studs and 17" wheels and front flairs to accomodate said wheels can wait. QUOTE(RON S. @ Dec 27 2006, 10:46 AM)  I'm gonna get my 930 front brakes installed by next weekend.That'll do it for me. Ron |
|
|
|
Posts in this topic
jr91472 Winter Projects.... Dec 27 2006, 08:57 AM
Vacca Rabite I am dwaddling on mine.
My sweetie keeps giving me... Dec 27 2006, 09:37 AM iamchappy Lets see my last Winters turbo car project became ... Dec 27 2006, 10:17 AM StratPlayer My winter project is moving right along, not much ... Dec 27 2006, 12:11 PM John Winter projects?
I haven't even gotten to my... Dec 27 2006, 12:40 PM rmital ...it ain't winter yet here...still waiting...... Dec 27 2006, 12:44 PM
brant definitely getting behind.
haven't even starte... Dec 27 2006, 01:53 PM 736conver Here's my winter project. Putting tile in the... Dec 27 2006, 03:14 PM tracks914 I've been busy too.
Stripped the car
Mounted i... Dec 27 2006, 06:22 PM tracks914 Then went to work on this
New frame rails complete... Dec 27 2006, 06:23 PM tracks914 and this
both sides and next on to the new floor..... Dec 27 2006, 06:24 PM Borderline Car is 99% disassembled: changing colors from Tang... Dec 27 2006, 07:57 PM race914 Removed my stock rear deck lid & spoiler (38lb... Dec 27 2006, 08:05 PM iamchappy Doug, your a way better man than me by saving that... Dec 27 2006, 09:20 PM Vacca Rabite Well today I welded up my side marker lights, as w... Dec 27 2006, 09:29 PM highways Well the restoration shop is almost finished- layi... Dec 27 2006, 09:59 PM tracks914
Doug, your a way better man than me by saving tha... Dec 27 2006, 10:03 PM MrKona Just did my first engine drop tonight. While the ... Dec 27 2006, 10:49 PM itsa914 My 914 is down at Shelby's (flatout) waiting i... Dec 27 2006, 11:05 PM Hammy Very minimal work on the 914. Just driving the hel... Dec 27 2006, 11:22 PM LowGT I can't start my winter 914 project until I se... Dec 27 2006, 11:32 PM TROJANMAN I just want heat!
hopefully my heater hoses w... Dec 27 2006, 11:46 PM Marv's3.6six Worked on my GT project on Sat the 16th. Fabricate... Dec 28 2006, 09:55 AM RonD Order set of bilstiens this morning.
Have parts ... Dec 28 2006, 01:18 PM
Ferg Job one is a external Oil Cooler, Oil Cooler parts... Dec 28 2006, 02:27 PM |
7 User(s) are reading this topic (7 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th January 2025 - 03:24 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.