 Any reason to *not* buy this inexpensive Metal Cutting Band Saw... |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Mid_Engine_914 |
 Dec 29 2006, 10:19 PM
Post
#1
|
|
Member  Group: Members Posts: 195 Joined: 22-September 06 From: Left Coast Member No.: 6,888  |
to cut steel tubing? I will probably only need to use it a few times a year but I want to make sure it makes accurate mitered cuts...
(IMG:http://ec1.images-amazon.com/images/P/B0000AXAYK.01-A1787XOD7Q2I4M._SS500_SCLZZZZZZZ_V39379494_.jpg) http://www.amazon.com/Northern-Industrial-...e=UTF8&s=hi |
   |
 
|
  |
Replies
| ChrisFoley |
Dec 30 2006, 07:22 AM
Post
#2
|
|
I am Tangerine Racing Group: Members Posts: 7,970 Joined: 29-January 03 From: Bolton, CT Member No.: 209 Region Association: None 
|
I used to have three of them at my shop until I bought a nice big saw. I still use one at the shop and have one at home as well.
They do not cut straight and the angle adjusting slot isn't well formed. The sheet metal support frame sucks, and the motor plate isn't sturdy enough. and so on... All of these issues can be dealt with if you are patient. One of the most useful upgrades I recommend is a better support frame made with square tubing. I also agree about the blade quality. You could buy a 100 ft coil of 1/2" wide Starrett bimetal blade material in a couple of tooth pitches, then find a fabrication shop with a blade welder. Paying them to weld blades should be cheaper than buying finished blades. I think you can get 18 blades from 100 ft. |
|
|
|
| brant |
Dec 30 2006, 08:56 AM
Post
#3
|
|
914 Wizard Group: Members Posts: 11,828 Joined: 30-December 02 From: Colorado Member No.: 47 Region Association: Rocky Mountains 
|
QUOTE(Racer Chris @ Dec 30 2006, 06:22 AM)  I used to have three of them at my shop until I bought a nice big saw. I still use one at the shop and have one at home as well. They do not cut straight and the angle adjusting slot isn't well formed. The sheet metal support frame sucks, and the motor plate isn't sturdy enough. and so on... All of these issues can be dealt with if you are patient. One of the most useful upgrades I recommend is a better support frame made with square tubing. I also agree about the blade quality. You could buy a 100 ft coil of 1/2" wide Starrett bimetal blade material in a couple of tooth pitches, then find a fabrication shop with a blade welder. Paying them to weld blades should be cheaper than buying finished blades. I think you can get 18 blades from 100 ft. chris, where do you buy these 100ft rolls of blade material? (any online resources?) brant |
|
|
|
Posts in this topic
Mid_Engine_914 Any reason to *not* buy this inexpensive Metal Cutting Band Saw... Dec 29 2006, 10:19 PM
scotty b Best bang for the buck IMO. I have used many diffe... Dec 29 2006, 10:38 PM Mid_Engine_914 Thanks for the advice. :thumbsup: Dec 29 2006, 10:46 PM PRS914-6 I have a Wilton that is similar. I've used it... Dec 29 2006, 11:09 PM Twystd1 Ditto on the good blades.
I use a place called ... Dec 29 2006, 11:31 PM Mueller also check out ENCO for the saw and blades...one o... Dec 30 2006, 12:42 AM McMark I'm glad this came up. A chop saw (which I re... Dec 30 2006, 01:37 AM John What's the problem with chop saws? I like the... Dec 30 2006, 01:47 AM
Racer Chris
What's the problem with chop saws? ...
Too l... Dec 30 2006, 07:29 AM Mid_Engine_914 In his "Working With Tubing" DVD Ron Cov... Dec 30 2006, 03:07 AM PRS914-6
I also agree about the blade quality. You could ... Dec 30 2006, 09:18 AM Bartlett 914 I get my band saw blades from MSC (mscdirect.com).... Dec 30 2006, 09:08 AM Racer Chris Go to the Starrett Catalog. In the Contact us pul... Dec 30 2006, 09:57 AM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th January 2025 - 04:02 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.