 Look y'all, I done welded iyut., My first try... |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| SGB |
  Jan 2 2007, 05:41 PM
Post
#1
|
|
just visiting  Group: Members Posts: 4,086 Joined: 8-March 03 From: Huntsville, AL Member No.: 404 Region Association: South East States  |
OK. It looks AWFUL. JUST AWFUL. But thes pieces are really and fully attached. Even actually fused like real welding in a few spots. I'm gonna keep practicing a little before I attempt car stuff, I think. (IMG:style_emoticons/default/smile.gif)
For a cheapie HF wire feed (not mig), it seems to work OK. Who has some good welding tips? I saw something on the almighty internet that indicated there might be primer of some kind? When do ya use this? What do I need to look out for? It's kinda fun. The biggest challenge is starting "in the dark". How easy is it to burn 914 sheet metal up? This is only a two setting unit- high or low. So far I've been using just low. So here is my sculpture. Now I really need a good cut-off tool.... Attached thumbnail(s) 
|
   |
 
|
  |
Replies
| nebreitling |
Jan 2 2007, 09:14 PM
Post
#2
|
|
Member Emeritus Group: Members Posts: 3,314 Joined: 26-March 03 From: San Francisco Member No.: 478 |
just my 02: don't go near your car with that thing. use it for mending fence or fixing a plow or something. even if you could get two pieces to fuse with it (without burning holes everywhere), do you want all that splatter all over your car?
|
|
|
|
| SGB |
Jan 2 2007, 09:22 PM
Post
#3
|
|
just visiting Group: Members Posts: 4,086 Joined: 8-March 03 From: Huntsville, AL Member No.: 404 Region Association: South East States |
QUOTE(nebreitling @ Jan 2 2007, 09:14 PM)  use it for mending fence or fixing a plow or something. (IMG:style_emoticons/default/chairfall.gif) AFTER I got it, I started reading up a little more. I would have preferred MIG, but dis is whut I got. I now realize that a mig joint is not only cleaner, it is stronger, too. Well, for the $, it can be a learner. Dr Evil still has my trans, so I get a while to see if I can make this work OK. |
|
|
|
Posts in this topic
SGB Look y'all, I done welded iyut. Jan 2 2007, 05:41 PM
McMark It's a start! :D
The Harbor Freight auto... Jan 2 2007, 05:58 PM
Heeltoe914 :agree:
It's a start! :D
The Harbor F... Jan 2 2007, 06:22 PM JPB Its flux core wire right? For mild steel I think ... Jan 2 2007, 06:35 PM SGB Thanks folks. The auto darkening helmet sounds li... Jan 2 2007, 08:10 PM Vacca Rabite So far all of the welding that I have done on my c... Jan 2 2007, 08:22 PM Crazyhippy yes you can weld upside down, burns are a bitch, b... Jan 2 2007, 08:30 PM PRS914-6 If you are going to try to weld body parts with an... Jan 2 2007, 09:29 PM alpha434 Get a welding book.
It helps to pre-heat the work... Jan 2 2007, 09:44 PM andys
And DON'T get a crappy auto-darkening helmet... Jan 2 2007, 09:57 PM McMark
And DON'T get a crappy auto-darkening helmet ... Jan 3 2007, 12:38 AM Air_Cooled_Nut
...And DON'T get a crappy auto-darkening helm... Jan 3 2007, 02:29 PM Krieger914 The HF helmut is $50. I took a welding class... Jan 2 2007, 10:21 PM John If you are using wire feed (not MIG) then you shou... Jan 2 2007, 10:39 PM highways Either go with a quality auto darkening or a quali... Jan 3 2007, 01:46 AM John Kelly Try welding with no gap. Gaps are for thicker mat... Jan 3 2007, 06:19 AM faux916 One should always practice welding on the wifes ca... Jan 3 2007, 08:22 AM spunone If ya can't see for shit when welding ya might... Jan 3 2007, 02:37 PM Lawrence Looks good, dude.
Come borrow my welding helmet, ... Jan 3 2007, 03:03 PM Lawrence And by good... I mean for a first try. You may NO... Jan 3 2007, 03:08 PM cooltimes I agree with Rusty. Not bad for a 1st time adventu... Jan 3 2007, 03:22 PM SGB WOW. Great site, Mike. Thanky much. Jan 4 2007, 08:16 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 31st October 2024 - 07:25 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.