 I Don't need no stinking jack stands, Got my lift today |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| carr914 |
 Jun 27 2007, 02:40 PM
Post
#1
|
|
Racer from Birth  Group: Members Posts: 119,389 Joined: 2-February 04 From: Tampa,FL Member No.: 1,623 Region Association: South East States   |
I got my Rotary Revolution7 lift installed in my garage today. Sahaha Beige Steve was kind enough to bring his M471 GT over to test it, as my Carrera is STILL at the paint shop. Thanks Steve, Thanks Rotary-Nice Lift.
T.C. Attached image(s) 
|
   |
 
|
  |
Replies
| JeffBowlsby |
Jun 28 2007, 09:55 PM
Post
#2
|
|
914 Wiring Harnesses Group: Members Posts: 8,579 Joined: 7-January 03 From: San Ramon CA Member No.: 104 Region Association: None 
|
So I have been thinking about getting 4 post lift but was wondering:
How does a 914 owner lift one rear wheel while the car is on the lift to do a valve adjustment? On the ground I use a ramp and a jackstand but is there is an easier way with a lift? How is brake work done while on the lift? A jackstand in the wheel channel? I doubt a standard floor jack will fit lengthwise under the rockers in the wheel tray. I have seen these center jacks available for the lift (more $$$) but they seem to lift the car from the center and I am not sure that is the right way for 914s... hep me... |
|
|
|
Posts in this topic
carr914 I Don't need no stinking jack stands Jun 27 2007, 02:40 PM
carr914 Another shot Jun 27 2007, 02:41 PM Ferg Your back will thank you! :thumbsup:
Ferg Jun 27 2007, 02:43 PM
mskala
:agree:
Also great for those other cars you m... Jun 28 2007, 11:28 AM RoninEclipse2G
:agree:
Also great for those other cars you ... Jun 28 2007, 11:35 AM orthobiz
be glad you don't have a touareg :headbang: ... Jun 28 2007, 07:49 PM sendjonathanmail where'd you get that??? Jun 27 2007, 02:59 PM Johny Blackstain Nice :thumbsup: . Nice car too :drooley: ! ... Jun 27 2007, 03:01 PM carr914 Source: www.revolutionlifts.com. I had it installe... Jun 27 2007, 03:19 PM michaelt55 whats it cost if you don't mind me asking? I... Jun 27 2007, 04:06 PM sendjonathanmail also curious....--JON Jun 27 2007, 04:30 PM watsonrx13 TC, lift looks great, especially with Steve's ... Jun 27 2007, 06:19 PM carr914 Cost is on the high side of lifts, but installatio... Jun 27 2007, 06:51 PM Air_Cooled_Nut
Cost is on the high side of lifts, but installati... Jun 28 2007, 10:12 PM 9146986 That's more than my two post asymmetrical Rota... Jun 27 2007, 07:30 PM Vacca Rabite So Jealous...
So....
Jealous.
Zach Jun 27 2007, 09:48 PM sendjonathanmail wow Jun 28 2007, 12:33 PM Gint
So I have been thinking about getting 4 post lift... Jun 28 2007, 09:59 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 28th June 2024 - 11:46 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.