 Floor pan rust inside! Found some in my LE, Pull your seat out & check yours |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| JRust |
 Oct 25 2011, 10:09 PM
Post
#1
|
|
914 Guru  Group: Members Posts: 6,313 Joined: 10-January 03 From: Corvallis Oregon Member No.: 129 Region Association: Pacific Northwest 
 |
Okay I was pulling my interior to install my new dash & backpad. Down by my seat hinge I see some rust around the hinge mount. It was between the sound deadening factory stuff & the mount. It started around the mount & worked it's way across. I had one tiny hole through & some spots if it hadn't been seen would have gone through. Another gift from my car sitting outside at the wrench who screwed me a while back. He just keeps giving & giving (IMG:style_emoticons/default/headbang.gif) .
So I scraped all the sound deadening off on the rear drivers side pan. I treated it with some rust stuff I have. Tonight I scraped off most the front sound deadening. It was great with the exception of a little more around the pedal. I can tell it is just surface rust but it is coming out. I plan to use bedliner to redo the floor. Then I am going to paint it L80E to match my car. Here are a few pics to check out of the area mostly scraped up. I haven't started on the passenger side but if it has the same issue I will get some before pics. What have you used to replace the sound deadening (IMG:style_emoticons/default/confused24.gif) Attached image(s)  
|
   |
 
|
Posts in this topic
JRust Floor pan rust inside! Found some in my LE Oct 25 2011, 10:09 PM
rjames you can use the dynomat stuff or similar product o... Oct 25 2011, 11:04 PM mark21742 I've used and plan to use truck bed liner........ Oct 26 2011, 04:58 AM rdauenhauer I used the reproduction tar mats that George offer... Oct 26 2011, 08:22 AM JRust Yeah I have a little bit of surface rust by my ped... Oct 26 2011, 11:09 AM SirAndy What have you used to replace the sound deadening ... Oct 26 2011, 11:18 AM
ConeDodger
What have you used to replace the sound deadening... Oct 26 2011, 11:24 AM JRust Who has the replacement tar mats? I didn't see... Oct 26 2011, 01:43 PM JRust Please tell me doubleA isn't the only place to... Oct 27 2011, 10:38 AM r_towle Are you seeking a replacement that appears to be s... Oct 27 2011, 10:49 AM SirAndy Lizard Skin
Any bed-liner, including "Lizar... Oct 27 2011, 11:18 AM r_towle
Lizard Skin
Any bed-liner, including "Liza... Oct 27 2011, 11:22 AM SirAndy Do you seriously get in and remove your floor mat ... Oct 27 2011, 11:23 AM jsayre914
I would suggest that you strip and epoxy paint th... Oct 27 2011, 05:28 PM JRust I'm going to test some bedliner product tonigh... Oct 27 2011, 01:00 PM SirAndy Getting something shipped in a timely manner can b... Oct 27 2011, 01:49 PM JRust
By far the quickest way would be to just clean th... Oct 27 2011, 03:58 PM Rand
Once my back recovers from all this scraping. I a... Oct 27 2011, 04:10 PM 70_914 JC Whitney sells sound deadener. Some of their st... Oct 27 2011, 01:55 PM bandjoey Ditto. HF milti tool cuts the old tar off in 30 m... Oct 27 2011, 04:19 PM ewdysar Hey I just looked under my driver seat... is this... Oct 27 2011, 05:31 PM SirAndy Hey I just looked under my driver seat... is this... Oct 27 2011, 05:59 PM ewdysar
Hey I just looked under my driver seat... is thi... Oct 27 2011, 06:23 PM dlestep There are natural harmonics of the 914
and then th... Oct 28 2011, 09:13 PM rdauenhauer
EDIT I am using 1/4 inch Solid Rubber sheeting I... Oct 28 2011, 11:19 PM dlestep
[quote name='dlestep' post='1563224' date='Oct 28... Oct 29 2011, 02:28 PM JRust Okay I am almost there cleaning up the floor. I al... Oct 29 2011, 10:01 PM JRust Spent a little more time last night. Got the passe... Nov 2 2011, 12:58 PM sixaddict The only way to varify good metal is strip is off ... Nov 2 2011, 07:35 PM  |
3 User(s) are reading this topic (3 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 4th January 2025 - 08:25 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.