 Twisted, Its still cockeyed |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Maine914 |
 Jun 7 2003, 05:47 PM
Post
#1
|
|
Member  Group: Members Posts: 99 Joined: 30-January 03 From: Maine Member No.: 215  |
My 1972 914 dips on the drivers side. In other words, its about an inch lower on that side. The tire has only a 1/2 clearance to the fender in back on the drivers side [which seems too small.] Based on the concensus of the 914Club BBS, I put on new springs [165s from PP.]. Springs look nice and shiny, but no change in the dip. I also looked under the car very closely -- there is no dignificant rust, and no sag. It is reputed that this car took a roll in an earlier life in CA. Is it possible the body is just twisted? If I can't get it untwisted, to be safer, would smaller tires make sense? It has 185s on it now with Riviera rims.
Thanks |
   |
 
|
Posts in this topic
Maine914 Twisted Jun 7 2003, 05:47 PM
SirAndy check the suspension console in the rear for crack... Jun 7 2003, 06:06 PM Maine914 I did...or think I did. Any tips on where to look... Jun 7 2003, 06:39 PM seanery the arm that connects to the rear wheel. look for ... Jun 7 2003, 06:49 PM mskala Don't fear the worst right away (unless you kn... Jun 7 2003, 07:22 PM DNHunt Did ya drive it. They often come off the jacks lop... Jun 7 2003, 08:20 PM SirAndy suspension console usally cracks above where the t... Jun 7 2003, 08:29 PM mskala If you are up to it and near southern maine, I am ... Jun 7 2003, 08:34 PM djm914-6 I wanna look to!!!
My vote is either ... Jun 7 2003, 08:57 PM Maine914 OK. Thanks. It would be helpful to have some fol... Jun 7 2003, 09:31 PM mskala A car is like a chair, too much height on one corn... Jun 7 2003, 10:17 PM Maine914 Thanks. It has carbs. And I did tune it up -- ne... Jun 8 2003, 06:29 AM Maine914 As my other post indicates, I continue to have eng... Jun 8 2003, 06:57 PM seanery Eventually, it will get better. :D
or
It will ... Jun 8 2003, 07:10 PM DNHunt It will get better. Yesterday I drove 2 exits past... Jun 8 2003, 08:17 PM Don Wohlfarth I'd recommend that you set down, take a deep b... Jun 9 2003, 02:01 PM mskala Overall, I agree. Unless this car has sentimental... Jun 9 2003, 04:19 PM nebreitling yes, make sure the frame is kosher before proceedi... Jun 9 2003, 07:58 PM Maine914 Thanks. SInce I'm in Maine, your Palo Alto sh... Jun 10 2003, 08:50 AM nebreitling too far? where's your commitment?!
:lol... Jun 10 2003, 10:27 AM
Maine914 My kid is out that way, and when I visited I testd... Jun 10 2003, 05:12 PM  |
4 User(s) are reading this topic (4 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 4th January 2025 - 11:41 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.