Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

859 Pages V  1 2 3 > »   
 Reply to this topicStart new topic
> what did you do to your 914 today
mrbubblehead
post Dec 17 2011, 08:07 PM
Post #1


Twodollardoug
***

Group: Members
Posts: 1,155
Joined: 17-December 10
From: calimesa ca.
Member No.: 12,492
Region Association: Southern California
i just wanted to start a thread to see what you guys do day to day on your cars.

i'll start,

about a month ago, i pulled my engine and trans to put in a new clutch. had the flywheel lightened and resurfaced. but what i didnt know is that i had to shim the little ball that the clutch arm rides on, after a resurfacing. so guess what i did today?

yup, pulled the trans and put an extra washer under the ball. you have to goop up both washers to get it to seal because the threaded hole goes all the way thru to the inside of the trans. i also replaced the plastic cup that the ball rides in. the throwout bearing and its little plastic blocks were fine so i buttoned every thing back up. 5 hours total. i think this has been the cheapest repair yet on my car. $2.75 for the little plastic cup.

what did you do to your 914 today?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
racerbvd
post Dec 17 2011, 08:17 PM
Post #2


Advanced Member
****

Group: Members
Posts: 2,369
Joined: 3-February 03
From: Sunny FL.
Member No.: 226
Region Association: None
I put a magetic wood dash kit on the dide (IMG:style_emoticons/default/shades.gif)

Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
ellisor3
post Dec 17 2011, 08:20 PM
Post #3


HPWhore
***

Group: Members
Posts: 811
Joined: 23-October 08
From: Fleming Island, Florida
Member No.: 9,683
Region Association: South East States
I put a new fan belt on my 3.2. What a suck fest. No way to get both hands near the pulley. When I was done my arms felt like Stretch Armstrong.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
shuie
post Dec 17 2011, 08:25 PM
Post #4


Member
**

Group: Members
Posts: 352
Joined: 17-May 04
From: baton rouge, la
Member No.: 2,075
(IMG:style_emoticons/default/sawzall-smiley.gif)

cut out my floors
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
windforfun
post Dec 17 2011, 08:29 PM
Post #5


Senior Member
***

Group: Members
Posts: 1,962
Joined: 17-December 07
From: Blackhawk, CA
Member No.: 8,476
Region Association: None
Q-tipped its ears.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Gustl
post Dec 18 2011, 12:27 AM
Post #6


914 enthusiast & historian
**********

Group: Members
Posts: 11,652
Joined: 16-June 04
From: TIROL / Austria
Member No.: 2,212
Region Association: Austria
yesterday I put my original leather steering wheel out of the car and replaced it with a newly leather covered one on a 30 mm longer hub (that gives me more leg space; I'm 6 ft 3")

today I will put out the "very custom" permatune installation out of the car and replace it with the original and newly rebuilt Bosch HKZ

Attached Image

after this I will set the car in hibernation mode (IMG:style_emoticons/default/biggrin.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
gendent
post Dec 18 2011, 12:51 AM
Post #7


Member
**

Group: Members
Posts: 89
Joined: 30-March 10
From: Lewison ID
Member No.: 11,528
Region Association: Pacific Northwest
I drove it to Costco, and back. Usually a 15 minute drive turned into 90 minutes. The long way home. No repairs. No break down. All back roads and no traffic. I did once worry I should be doing something else, but I got over that. Maybe tomorrow I will actually repair something.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Bob L.
post Dec 18 2011, 12:53 AM
Post #8


Senior Member
***

Group: Members
Posts: 848
Joined: 7-August 11
From: Austin TX
Member No.: 13,411
Region Association: Southwest Region
I put the bumperetts back on the front and began removing the fuel system for cleaning.

Gendent: Sounds like a thorough test drive and shake down. you should be proud. (IMG:style_emoticons/default/biggrin.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
PancakePorsche
post Dec 18 2011, 01:29 AM
Post #9


Member
**

Group: Members
Posts: 236
Joined: 29-July 11
From: Southern California
Member No.: 13,373
Region Association: None
Welded in Autopower roll cage, installed repainted fuel tank. Ready for track in two more weeks !!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cwpeden
post Dec 18 2011, 01:42 AM
Post #10


Great White North, huh?
***

Group: Members
Posts: 916
Joined: 20-August 06
From: Victoria BC
Member No.: 6,693
Region Association: Canada
Started it, wamred it up, turned it off. Then wished I had more time to fix the brakes.

Dumped half the res. of brake fluid on the floor of the carport for no apparent reason. Right off the master cylinder. Figure its the stupid hard lines from the res. They were a !@#!@ to get in.....or was it just me?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
infraredcalvin
post Dec 18 2011, 02:12 AM
Post #11


Distracted Member
***

Group: Members
Posts: 1,564
Joined: 25-August 08
From: Ladera Ranch, CA
Member No.: 9,463
Region Association: Southern California
QUOTE(PancakePorsche @ Dec 17 2011, 11:29 PM) *

Welded in Autopower roll cage, installed repainted fuel tank. Ready for track in two more weeks !!


Would you mind starting a thread with pics on this one? I have a stable energies bolt in cage that I have an idea how it goes in, but would like to see others' solutions.

Sorry to hijack, back to the topic... I went to the shop and wished my baby a merry Xmas, hopefully Santa will bring some tools (a welder) so I can start spending some quality time again...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
etcmss
post Dec 18 2011, 06:06 AM
Post #12


etcmss
**

Group: Members
Posts: 183
Joined: 20-April 06
From: Lancaster, Ky
Member No.: 5,899
Region Association: Upper MidWest
Prep the front suspension for removal..down to the last 2 bolts. out it comes
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bulitt
post Dec 18 2011, 06:43 AM
Post #13


Achtzylinder
****

Group: Members
Posts: 4,188
Joined: 2-October 11
Member No.: 13,632
Region Association: South East States
Picked up a fresh 327 SBC from a Nascar Mechanic. Xmas present for my 914.
Bored .060 over = 338 c.i. @ 330hp, Hi rev cam, roller rockers, etc. !
(IMG:style_emoticons/default/biggrin.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Phoenix-MN
post Dec 18 2011, 12:01 PM
Post #14


Senior Member
***

Group: Members
Posts: 927
Joined: 23-January 04
From: ST. Bonifacius,MN
Member No.: 1,590
No words needed (IMG:style_emoticons/default/shades.gif) and yes, it's cold in the garage...

Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
914itis
post Dec 18 2011, 12:07 PM
Post #15


Advanced Member
****

Group: Members
Posts: 2,892
Joined: 9-October 10
From: New York City
Member No.: 12,256
Region Association: North East States
I started to reassemble the engine. Installing the thins , cleaned fan shroud
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BuddyV
post Dec 18 2011, 12:50 PM
Post #16


Robert
***

Group: Members
Posts: 563
Joined: 8-April 05
From: Santa Rosa, CA
Member No.: 3,898
Region Association: Northern California
I replaced my 180 rear springs with 140s yesterday.

User is offlineProfile CardPM
Go to the top of the page
+Quote Post
gary gartner
post Dec 18 2011, 12:54 PM
Post #17


i know more than a newbie---way less than a guru
**

Group: Members
Posts: 239
Joined: 16-December 04
From: Valencia, Ca
Member No.: 3,294
Region Association: Southern California


I will dust him off, clean up and get reaady for the SoCal Hangover run

That is all Folks

Gary (IMG:style_emoticons/default/beerchug.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
MrHyde
post Dec 18 2011, 01:25 PM
Post #18


Senior Member
***

Group: Members
Posts: 525
Joined: 13-October 10
From: Ontario, Canada
Member No.: 12,268
Region Association: None
Finished welding a few touchups on the rear floor pan top-side..

Welded in the Tangerine racing rear inner suspension ear reinforcements.. Then ground the welds and rattle-can primer.

Then started taking apart one of the trailing arms.. got the calliper, rotor, shock/spring, dust shield off. Then started looking on here for an easier way to get the hub and bearing out.

Next I have to deep fry a turkey for about 8-10 people tonight.

Oh.. and it snowed a bit.... not enough to break out my snowboard, but its starting to feel like Christmas
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mrbubblehead
post Dec 18 2011, 01:45 PM
Post #19


Twodollardoug
***

Group: Members
Posts: 1,155
Joined: 17-December 10
From: calimesa ca.
Member No.: 12,492
Region Association: Southern California
nothing.....its raining....ARGH! (IMG:style_emoticons/default/hissyfit.gif) (IMG:style_emoticons/default/hissyfit.gif) (IMG:style_emoticons/default/hissyfit.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
stugray
post Dec 18 2011, 02:13 PM
Post #20


Advanced Member
****

Group: Members
Posts: 3,825
Joined: 17-September 09
From: Longmont, CO
Member No.: 10,819
Region Association: None
Finished cleaning the last of my parts fro my Dual Weber rebuild in the ultra-sonic parts washer.

Touching up roll cage & reinstall after all new interior.
Replaced seat rails with race adjustable & grade 8 bolts.

Stripped & repainted the hellhole from PO's silicone mess.

Repainting the rear firewall engine side.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

859 Pages V  1 2 3 > » 
Reply to this topicStart new topic
7 User(s) are reading this topic (7 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 31st October 2024 - 06:17 PM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...