 porsche crest: -light hearted question, Proper place??? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| lostmybaby |
 Jan 15 2003, 10:41 PM
Post
#1
|
|
Newbie  Group: Members Posts: 10 Joined: 13-January 03 Member No.: 143  |
Heres a good one. 914s did not come with a porsche crest, correct? However, most 914s on the street today have the crest on the front hood. So, if the crest is on the hood when you buy the car, what is the proper placement location.
I have seen the crest low on the hood, about an inch from the front, and I have seen the crest higher on the hood, roughly 4 inches from the front of the hood. If placed, where is the preferred location? |
   |
 
|
| campbellcj |
Jan 15 2003, 10:45 PM
Post
#2
|
|
I can't Re Member Group: Members Posts: 4,597 Joined: 26-December 02 From: Agoura, CA Member No.: 21 Region Association: Southern California 
|
If it were me doin' the drillin' (which it won't be) I would put it in approx the same location as on the short-hood 911's. A few inches up but I don't know the exact measurement.
|
 |
|
| olav |
Jan 15 2003, 10:46 PM
Post
#3
|
|
Senior Member Group: Retired Members Posts: 1,107 Joined: 28-December 02 From: Los Gatos, CA. USA Member No.: 34 Region Association: None |
Mine came with the car and it is the exact same distance up the hood as a contemporary 911.
I never really noticed the variation between 914s though, never looked I suppose. - Olav |
|
|
|
| lostmybaby |
Jan 15 2003, 11:01 PM
Post
#4
|
|
Newbie Group: Members Posts: 10 Joined: 13-January 03 Member No.: 143 |
Yeah, I guess most people dont notice. I just happen to notice when looking at different pictures online. The variation isnt that easy to notice until you find two pictures of two really nice restored cars.
|
|
|
|
| bobp |
Jan 15 2003, 11:19 PM
Post
#5
|
|
Newbie Group: Members Posts: 17 Joined: 8-January 03 Member No.: 115 |
Mine is low on the hood, it was on the car when I bought it. I kind of like it, but if my hood wasn't already drilled, I probably wouldn't put one on at all. Drilling holes in non galvanized body parts seems to me to be inviting rust.
I never noticed different placements, but then 914s are rare in Buffalo. I have only seen a couple in the area. I doubt there were very many in the 70s, and any sold here originally, have returned to the iron oxide from which they were made by now. |
|
|
|
| Brad Roberts |
Jan 16 2003, 12:15 AM
Post
#6
|
|
914 Freak! Group: Members Posts: 19,148 Joined: 23-December 02 Member No.: 8 Region Association: None |
They mount them low and high because of the hood cross brace runs right there. Some people dont mess with the brace and mount them above it. I promise the low ones had to have work done to the cross brace.
B |
|
|
|
| echocanyons |
Jan 16 2003, 09:18 AM
Post
#7
|
|
Advanced Member Group: Benefactors Posts: 2,096 Joined: 24-December 02 From: Bay Area, CA Member No.: 7 Region Association: Central California 
|
PP has a tech article:
http://www.pelicanparts.com/techarticles/9..._hood_crest.htm complete with template |
|
|
|
| tracks914 |
Jan 16 2003, 08:34 PM
Post
#8
|
|
Canadian Member Group: Benefactors Posts: 2,083 Joined: 15-January 03 From: Timmins, Ontario, Canada Member No.: 153 Region Association: None |
Mine came with one high on the hood but it wasn't drilled. It was fastened with two sided trim tape. It wasn't easy to take off but at least the hood wasn't drilled. If I put it back on, it will be with tape again.
|
|
|
|
| rick 918-S |
Jan 16 2003, 11:30 PM
Post
#9
|
|
Hey nice rack! -Celette Group: Members Posts: 20,833 Joined: 30-December 02 From: Now in Superior WI Member No.: 43 Region Association: Northstar Region 
|
I would perfer to see them mounted on a wood plaque or as a decoration on a desk top pen holder. IMHO They fall into the same catagory as those windsheid banners that tell everyone what your driving. I know that my post isn't answering the original question but I hate those things. Weld the holes up. We all know what we have. What else... Sorry if I've ticked anyone off.
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd January 2025 - 12:28 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.