 ENGINE TEST Stand, show me you engine test stand build |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| 02loftsmoor |
  Sep 27 2015, 11:18 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 577 Joined: 26-June 11 From: Ft. Worth TX Member No.: 13,243 Region Association: Southwest Region 
 |
Over the years I've seen you guys build temporary engine test stand out of wood to run the engine out of the car, post your pictures. I need to put some thing together to run my engine. and thank you all. (IMG:style_emoticons/default/driving.gif)
|
   |
 
|
| Bills914-4 |
Sep 27 2015, 01:29 PM
Post
#2
|
|
Member Group: Members Posts: 311 Joined: 1-March 08 From: suburbs of Miami FL. Member No.: 8,762 Region Association: South East States |
Sorry it's not a wood stand , but I modified my engine assembly stand , I cut the down
tube & welded in another slip tube for the old v8 yolk plate, I pick up a vw bus bellhousing off samba ( $30 (IMG:style_emoticons/default/smile.gif) ) , I mounted it low for balance , here's a few pictures , I also made a battery tray with a instrument panel with some extra gauges I had , Bill D.      |
|
|
|
| rhodyguy |
Sep 27 2015, 02:54 PM
Post
#3
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,192 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
I was trying to figure out the purpose of the bell housing. Clever way to lower the center of gravity.
|
|
|
|
| zambezi |
Sep 27 2015, 02:59 PM
Post
#4
|
|
Senior Member Group: Members Posts: 711 Joined: 14-April 08 From: Lafayette, LA Member No.: 8,920 Region Association: South East States |
Heres mine that I use to run up 356 engines.
   |
|
|
|
| 02loftsmoor |
Sep 27 2015, 03:30 PM
Post
#5
|
|
Senior Member Group: Members Posts: 577 Joined: 26-June 11 From: Ft. Worth TX Member No.: 13,243 Region Association: Southwest Region
|
WOW good stuff, I do have a bell housing.
|
|
|
|
| jimkelly |
Sep 27 2015, 05:11 PM
Post
#6
|
|
Delaware USA Group: Members Posts: 4,969 Joined: 5-August 04 From: Delaware, USA Member No.: 2,460 Region Association: MidAtlantic Region |
here is mine - engine on a pallet - and a board mounted vertically to hold a couple of switches and fuel pump.
https://www.youtube.com/watch?v=3MFdcY-DqqI |
|
|
|
| VaccaRabite |
Sep 27 2015, 05:59 PM
Post
#7
|
|
En Garde! Group: Admin Posts: 13,589 Joined: 15-December 03 From: Dallastown, PA Member No.: 1,435 Region Association: MidAtlantic Region |
(IMG:http://www.914world.com/bbs2/uploads_offsite/c2.staticflickr.com-1435-1443398381.1.jpg)
For carbs its easy, you only need a few circuits. Starter. Fuel. Ignition. I also put a simple tach on the control panel, just for kicks. Zach |
|
|
|
| trojanhorsepower |
Sep 27 2015, 06:13 PM
Post
#8
|
|
Senior Member Group: Members Posts: 867 Joined: 21-September 03 From: Marion, NC Member No.: 1,179 Region Association: None |
Stratplayer has a good one. I will try and dig up the thread.
|
|
|
|
| trojanhorsepower |
Sep 27 2015, 06:21 PM
Post
#9
|
|
Senior Member Group: Members Posts: 867 Joined: 21-September 03 From: Marion, NC Member No.: 1,179 Region Association: None |
|
|
|
|
| 02loftsmoor |
Sep 28 2015, 09:24 PM
Post
#10
|
|
Senior Member Group: Members Posts: 577 Joined: 26-June 11 From: Ft. Worth TX Member No.: 13,243 Region Association: Southwest Region
|
Good stuff guys!!
|
|
|
|
| mbseto |
Sep 29 2015, 02:51 PM
Post
#11
|
|
Senior Member Group: Members Posts: 1,257 Joined: 6-August 14 From: Cincy Member No.: 17,743 Region Association: North East States |
I would love to see the wiring diagrams that go with these! Esp. if d-jet is involved.
|
|
|
|
| Spoke |
Sep 29 2015, 08:01 PM
Post
#12
|
|
Jerry Group: Members Posts: 7,087 Joined: 29-October 04 From: Allentown, PA Member No.: 3,031 Region Association: None
|
Engine sitting on a Harbor Freight dolly. Engine stand holding up the engine-coolant-overflow gas tank...
https://www.youtube.com/watch?v=eOC3oVgZlCM |
|
|
|
| 3d914 |
Oct 2 2015, 07:28 PM
Post
#13
|
|
Senior Member Group: Members Posts: 1,275 Joined: 24-September 03 From: Benson, AZ Member No.: 1,191 Region Association: Southwest Region |
rhody, here's the test stand I built from ebay plans for $150. I modified to serve as dolly and to hoist the engine for installation.
(IMG:http://www.914world.com/bbs2/uploads/post-1191-1354150116.jpg) Here's a video of last test run of SHO 3.2 V6 |
|
|
|
| StratPlayer |
Oct 3 2015, 10:02 AM
Post
#14
|
|
StratPlayer Group: Members Posts: 3,298 Joined: 27-December 02 From: SLC, Utah Member No.: 27 Region Association: Rocky Mountains 
|
Here's the one I put together http://www.914world.com/bbs2/index.php?sho...c=81485&hl=
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 25th November 2024 - 01:34 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.