Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

2 Pages V  1 2 >  
 Reply to this topicStart new topic
> Engine is slooowly coming together, Here's the shortblock
Qarl
post Jun 13 2003, 03:31 PM
Post #1


Shriveled member
*****

Group: Benefactors
Posts: 5,233
Joined: 8-February 03
From: Florida
Member No.: 271
Region Association: None
Finally remembered to bring the camera to take a picture of the shortblock. or the mid-block. It's not quite a long block yet.

Cylinder heads are getting new studs, valves, and valve springs. Cams are on order.

Nice and shiny 98mm J&E Pistons and cylinders.

Regards,


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Aaron Cox
post Jun 13 2003, 03:34 PM
Post #2


Professional Lawn Dart
***************

Group: Retired Admin
Posts: 24,541
Joined: 1-February 03
From: OC
Member No.: 219
Region Association: Southern California
thas purdy

way cool....thanx for the pics
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Lawrence
post Jun 13 2003, 03:46 PM
Post #3


Senior Member
***

Group: Benefactors
Posts: 1,661
Joined: 5-February 03
Member No.: 244
Region Association: None
Someday I'll get to do my own engine, too.

It doesn't really *need* it now... but it sure would be fun. (IMG:style_emoticons/default/smile.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Aaron Cox
post Jun 13 2003, 04:02 PM
Post #4


Professional Lawn Dart
***************

Group: Retired Admin
Posts: 24,541
Joined: 1-February 03
From: OC
Member No.: 219
Region Association: Southern California
is one able to do a 911 engine with common hand tools? lika a type IV? or is it lots harder than that?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mark Henry
post Jun 13 2003, 04:33 PM
Post #5


that's what I do!
***************

Group: Members
Posts: 20,065
Joined: 27-December 02
From: Port Hope, Ontario
Member No.: 26
Region Association: Canada
QUOTE(acox914 @ Jun 13 2003, 02:02 PM)
is one able to do a 911 engine with common hand tools? lika a type IV? or is it lots harder than that?

One needs some special tools for setting up the cams, you can make homemade tools but you will also need a dial indicator.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
elmonte
post Jun 13 2003, 04:47 PM
Post #6


Member
**

Group: Members
Posts: 225
Joined: 31-March 03
From: Danville.ca
Member No.: 499
Looks real nice Karl What kind of compression ratio ? cams? intake?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Qarl
post Jun 13 2003, 04:54 PM
Post #7


Shriveled member
*****

Group: Benefactors
Posts: 5,233
Joined: 8-February 03
From: Florida
Member No.: 271
Region Association: None
I didn't mean to mislead people. I'm not building the engine.

Harro Zitza from Zotz Racing here in Winter Park, Florida is building it. He's in his late sixties maybe 70 or so. Been building and racing Porsches for 40+ years.

These are the specs.

1979 3.0L SC core - disassembled - magnafluxed, polished, crank and rods, blah blah

Early SC heads with the larger intakes and single plugs - new valves, springs, guides, etc.

98mm J&E Pistons & Cylinders 9.8:1 CR optimized for carbs with deeper valve recesses

Elgin Modified S cams (not quite as peaky, but the displacement will help smoothe out some of the peakiness anyways)

Electromotive Distributorless Ignition

New Oil Cooler

3.6L Carrera Oil Pump

46mm Weber IDA carbs

Kennedy Performance 9" Clutch Package flywheel, and Stage II pressure plate...

It will be a 3.2L short stroke when finished.

Should put out 250-260 ponies.... (IMG:style_emoticons/default/MDB2.gif)

Moowaahahaaaa
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Mueller
post Jun 13 2003, 05:00 PM
Post #8


914 Freak!
***************

Group: Members
Posts: 17,150
Joined: 4-January 03
From: Antioch, CA
Member No.: 87
Region Association: None
QUOTE
acox914 Posted on Jun 13 2003, 03:02 PM
----------------------------------------------------------------------
is one able to do a 911 engine with common hand tools? lika a type IV? or is it lots harder than that?


Vise-grips and a hammer is all that is needed (IMG:style_emoticons/default/smash.gif)

Wayne @ Pelican wrote a nice book on rebuilding the 911 engine...good reading...of course Bruce Andersons 911 Performance Handbook is a must if you ever consider a 911 or just a 911 engine.........
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
ChrisReale
post Jun 13 2003, 05:00 PM
Post #9


Sleazy
****

Group: Members
Posts: 2,665
Joined: 20-January 03
From: San Francisco
Member No.: 176
Karl, I know yo said it is for a street car, but if you dont AX it, Im gonna take it personally! Seriously, that would be a blast to take through some cones (IMG:style_emoticons/default/MDB2.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
elmonte
post Jun 13 2003, 05:01 PM
Post #10


Member
**

Group: Members
Posts: 225
Joined: 31-March 03
From: Danville.ca
Member No.: 499
If your the one with the money and the one who says
what going in it then your the one building the motor (IMG:style_emoticons/default/biggrin.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
maf914
post Jun 14 2003, 07:42 AM
Post #11


Not a Guru!
****

Group: Members
Posts: 3,049
Joined: 30-April 03
From: Central Florida
Member No.: 632
Region Association: None
Karl,

I don't know much about 911 parts, but who makes the cylinders which you indicate as J&E? Or are these Porsche cylinders with J&E pistons? Just curious because I thought the number or sources for Nickasil or Alumisil cylinders was very limited.

Mike
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Qarl
post Jun 14 2003, 08:22 AM
Post #12


Shriveled member
*****

Group: Benefactors
Posts: 5,233
Joined: 8-February 03
From: Florida
Member No.: 271
Region Association: None
The cylinders are from EBS racing (pistons too). I think the cost is like $950 for a set of cylinders on exchange. Or you have to pay a core fee. They are not new... but redone and new Nikasil applied.

Pistons are new.

www.ebsracing.com
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
914Timo
post Jun 16 2003, 05:44 AM
Post #13


*******
***

Group: Members
Posts: 743
Joined: 13-January 03
From: Finland
Member No.: 137
Region Association: Europe
Wow, looks good. (IMG:style_emoticons/default/clap56.gif)

Dont forget to take camera with you next time you visit there. At least I would like to see more pics and heard the latest news. Your engine (and the hole car) will be really nice and interesting.

About those pistons and cylinders, did the $950 includec the pistons also ?? If not, may I ask how much they were ??

I just asked from Andial how much the real new Mahle big bore kit is. Pete Sanchez was very nice and told me the price for a set of the 3.2 from 3.0 pistons and cylinders is $3547. (IMG:style_emoticons/default/blink.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Qarl
post Jun 16 2003, 05:48 AM
Post #14


Shriveled member
*****

Group: Benefactors
Posts: 5,233
Joined: 8-February 03
From: Florida
Member No.: 271
Region Association: None
It's not that much cheaper at EBS Racing.

I think everything ran under $3K (Pistons and Clyinders)... don't have the order in front of me... but not cheap!
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
914Timo
post Jun 16 2003, 06:04 AM
Post #15


*******
***

Group: Members
Posts: 743
Joined: 13-January 03
From: Finland
Member No.: 137
Region Association: Europe
OK, it was cylinders only. Many thanks about the info.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Qarl
post Jul 24 2003, 05:59 PM
Post #16


Shriveled member
*****

Group: Benefactors
Posts: 5,233
Joined: 8-February 03
From: Florida
Member No.: 271
Region Association: None
Long block is almost done.

Just waiting to install the rocker arms...

I pick up the fan and fan shroud from the powder coater tomorrow (along with headlight buckets, and pedal cluster pieces).

Carbon Fiber shroud and watershields should be here tomorrow or Monday and then the rest of the engine can come together...


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Qarl
post Jul 24 2003, 06:01 PM
Post #17


Shriveled member
*****

Group: Benefactors
Posts: 5,233
Joined: 8-February 03
From: Florida
Member No.: 271
Region Association: None
Tensioner and cam sprockets... Elgin S-cams have been timed. (Pretty much the same grind as the GE60).


Attached image(s)
Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
ChrisReale
post Jul 24 2003, 07:03 PM
Post #18


Sleazy
****

Group: Members
Posts: 2,665
Joined: 20-January 03
From: San Francisco
Member No.: 176
Way cool Karl. The time is getting closer and closer. Bet you cant wait to plant your ass in the seat and fire it up for the first time! (IMG:style_emoticons/default/beerchug.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Dave Cawdrey
post Jul 24 2003, 07:07 PM
Post #19


Dumbo going poop, Daddy :)
***

Group: Members
Posts: 818
Joined: 22-January 03
From: Seattle, WA USA
Member No.: 182
OMG!!

(IMG:style_emoticons/default/smilie_pokal.gif)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Brad Roberts
post Jul 25 2003, 12:05 AM
Post #20


914 Freak!
***************

Group: Members
Posts: 19,148
Joined: 23-December 02
Member No.: 8
Region Association: None
Nice.. No HYD. tensioners.

Looks great Karl. You done good..

I could have gotten you some slack on the P+C's.. I'm pretty tight with Don and the group at EBS.


B
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
« Next Oldest · 914World Garage · Next Newest »
 

2 Pages V  1 2 >
Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Display Mode: Standard · Switch to: Linear+ · Switch to: Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

- Lo-Fi Version Time is now: 31st October 2024 - 10:25 PM
Invision Power Board v9.1.4 © 2024  IPS, Inc.
All rights reserved 914World.com © since 2002
914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...